Please Scroll Down "In Sterling Silver and Tufa Stone Sandcast" Gary was born a Navajo in Ft. Defiance, Arizona and raised near Gallup, New Mexico. He attended schools in Phoenix, Arizona and Gallup, New Mexico. His interest in Navajo Silverwork came along in January of 1989. His parents are longtime Silversmiths and have a well-known background of old Traditional Indian Jewelry. His business "Twin Feather Designs" came to be when his mother handed down some of the old sandcast samples of her work. Some of her pieces date back to the 1800's. He calls his business "Twin Feather" because of his mother's traditional work and his contemporary jewelry work. He put them together and does both sandcast contemporary plate work. He combines the two to give them a contemporary, Indian background design. Several southwest galleries now carry Gary's work including the Heard Museum, Phoenix, the Toh-Atin Gallery in Durango, the Phoenician Resort in Phoenix, Arizona and the Squash Blossom in Colorado Springs, and the East Coast. Gary began entering Indian Art Shows in March of 1990. Some of the shows that Gary has regularly attended are Heard Museum Indian Market in Phoenix, Arizona, the Indian Market in Santa Fe, New Mexico, and Eight Northern Pueblo Show in San Juan Pueblo. He sells his work only to Galleries, Museums, Resorts, and some well known shops throughout the country. He is now expanding his artwork to us here at Arizona Indian Jewelry.com, Westchester, New York and England. The work of Gary Custer is considered among the businesses as a very fine line of Contemporary Indian Artwork. Tufa is porous rock made of volcanic ash used to form a casting mold. The Tufa Stone is cut to the desired size and shape which often resembles a brick. It is then sliced in half. Usually, a design is carved into just one of the interior sides of the Tufa Stone. After the carving is done, the two halves of the Tufa Stones are rightly joined. This is tied together with a strip of rubber. A "sprue hole" is carved into one end. The joined and decorated halves then become the mold. Finally, molten sterling silver is poured through the "sprue hole" into the mold. After the sterling silver cools and hardens, the carved design is visible and the Tufa leaves a textured surface on the metal. Jewelry such as a bracelet is cast flat and then hammered into shape. Sandcast jewelry was first created by Navajo silversmiths sometime between 1840 and 1860. The basis of this process is a mold made by carving the desired design into a stone. Using this mold, a piece of jewelry is made (belt budkle, bracelet, ring, etc.) and becomes the "master sample" from which the subsequent sandcast pieces are made. Sandcasting is a labor intensive, hand process not to be mistaken with centrifugal and vacuum casting processes. Artisans using this method estimate that it takes approximately three days from start to finish to make a medium sized bracelet. Sandcasting evolved from casting using sandstone or tufa stone, a relatively soft stone created from compacted volcanic ash. Sandstone held up better but the tufa was easier to carve. The process involves many steps, starting by cutting a stone in half and grinding both halves until smooth on the cut side. The tufa stone is sometimes soaked in water to keep dust down and to make it carved in reverse on one of the smoothed halves. Then a cone shaped channel is carved from one edge of the design to the outer edge of the stone. A corresponding channel is carved on the half. When the two halves are fitted together, this channel becomes the passage way by which the molten silver is poured into the mold. Superheated air trapped in the mold can ruin a design. To prevent this, vents are carved from the extremenities of the design out toward the edge of the stone, allowing the air to escape. The stone mold is heated with a torch until it is carbon smoked on the inside of both halves. This prevents the silver from sticking to the mold. The mold is now ready for casting. The two pieces of the tufa stone are placed together with the pour channels aligned. Originally the pieces were held together by placing strips of wet leather around the stone. As the leather dried, it would shrink slightly and bind the two pieces of stone tightly together. Today, artisans use a number of methods, such as wrapping with wire, plywood board and clamps, or rubber straps. Following the completion of the stone mold, the silver is heated in a crucible with a torch until it is the right temperature, approximately 1850 degrees. Historically, temperature was judged by the color of the molten silver. That is still the most common method used even though many artisans now have access to crucibles with digitally controlled heat. Such fine control increases the chance for a successful pour. The temperature of the outside air must also be taken into consideration. If it is very cold, the silver can become too cool before it runs through the mold. When the silver is judged to be hot enough, it is poured into the mold through the previously carved channel. The force of gravity pulls the molten silver down through the channel and into the carved mold. Thus the piece is said to have been gravity cast. The tufa stone mold is allowed to cool and the silver piece is removed. Extra silver from the pour channel and the air vents are cut off (debarring) and placed back into the crucible to be reclaimed for future use. A tufa mold may allow several pours if the design is small and relatively simple. With larger, more complex designs, one or two pours is usually all that can be made from a tufa mold before the stone breaks or the design is ruined by the heat of the silver. The piece is finished by buffing, filing, soldering on findings, setting stones, etc. and the piece is ready for the consumer, however, if the piece obtained from the tufa casting is good enough, the artisan may decide to use it as a "master sample" (a model) in the sandcasting process. The process of sandcasting is very similar to that of the tufa casting just described, with the exception of the necessity of carving a new design. In place of carving a new design, the piece obtained from the tufa casting is used to make the mold in casting sand, a 60/40 mixture or dry cement and oil. The master sample is placed face up on the bottom of a wooden frame. The casting sand is packed down over the master until the frame is filled and firmly packed, completely covering the master piece. The top of the frame is then covered with plywood, cut to size, and turned over so that the bottom is now on top. The artisan moves the frame containing the sand master around on the work surface in a circular motion. This is to ensure that the sand has totally covered the master so that all the design elements will be completely captured. When the wooden covering is removed, the master piece, embedded in the sand is exposed. It must be lifted out of the sand taking great care not to disturb the impression left in the sand. This impression in the sand becomes the new mold and its preparation is much the same as that of the tufa mold. A channel for the molten silver and air vents are carved into the mold with a knife. A flat tufa stone is placed against the wooden frame and held together by means of rubber straps. Once again, the molten silver is gravity fed into the mold via the pour channel. The silver begins to harden almost as soon as it is poured so the artisan must work quickly. The frame is turned so that the silver is resting on the tufa side of the mold. The frame containing the sand is lifted off leaving the silver piece sitting on the tufa stone. The process must be repeated for each piece of jewelry as the sand mold is destroyed by the heat of the molten silver. At this point, the silver is still very hot and so, while holding it with the pliers, the slag is cut off and it is dipped into an acid for cleaning. After debarring, different shapes of files; round, oval, square, etc. are used to smooth out the silver. These files leave marks on the silver which must be buffed if a highly polished piece is desired. If the file marks are not removed before stones and findings are added, some of them may not be removable and the finish will have an older, more traditional look. Any decorative work (i.e. bezels, twist wire) is added by means of soldering with a torch. And any findings or backings, such as the swivel and catch on a buckle, are added. The piece is washed in hot waster with a mild soap and a soft brush and is now ready to be polished. Polishing takes place in two stages. First the silver piece is polished with a wax and then must be washed again to remove the excess wax. After that comes dry polishing with either buckskin or a dry cloth wheel. And finally, stones, if any, are set. As previously mentioned, tufa and sandcasting processes are extremely labor intensive. Carving the original design into the tufa stone can take as much as 16 hours, depending upon the complexity of the design. In addition, there are the hours of cleaning up, buffing, polishing, adding design elements, and setting stones. The finished piece has cost the artisan many hours which must be taken into account in setting the price of jewelry created by this method. Thank You ~ Gary S. Custer ! . |